产品中心
新闻动态 当前位置:首页>新闻动态>新闻动态

造型机的使用要点

网址:www.zaoxingji.com.cn  2020-09-14  作者:admin    阅读:

造型机安全操作的要点如下:
The key points of safe operation of molding machine are as follows:
1、造型机使用时,操作者应熟悉造型机的机械部件、电器部件、动作程序、润滑系统等情况,以及设备使用中规定的其它要求。  造型机紧实砂型程序4个步骤:振实、压头摆入、压实、压头摆出  造型机起模程序:工作台夹紧、起模杆升起、运走砂箱、机箱部复位
1. When using the molding machine, the operator should be familiar with the mechanical parts, electrical components, action procedures, lubrication system, and other requirements specified in the use of the equipment. There are four steps in the molding machine compaction sand mold procedure: vibration compaction, indenter swing in, compaction, pressure head swing out molding machine mold lifting procedure: worktable clamping, mold lifting rod lifting, sand box transportation, case reset
2、造型机使用时,开动设备前,应先检查造型机的润滑装置是否完善,并按规定加油,检查各紧部件是否紧固,各操作手柄是否处于零位(空位),气阀动作是否灵活,管路有无漏气,然后打开总气阀放掉管路中的积气和积水。         3、严禁开空车,必须在有载荷的情况下进行试车,检查各工作状态是否正常,对应该加油的地方进行加油润滑。试车正常后方可进行工作。
2. When using the molding machine, before starting the equipment, check whether the lubrication device of the molding machine is perfect, and add oil according to the regulations, check whether the tight parts are tight, whether the operating handle is at zero position (empty position), whether the air valve acts flexibly, whether there is air leakage in the pipeline, and then open the main gas valve to drain the accumulated gas and water in the pipeline. 3. It is strictly forbidden to drive an empty car. The test run must be carried out under the condition of load. Check whether the working conditions are normal, and lubricate the places where oil should be added. Work can be carried out after the test run is normal.
4、造型机使用时要认真观察运转情况,在操作中应经常用空气吹净润滑部位和运转部位的砂粒,严禁各润滑部位粘砂。
4. The operation of the molding machine should be carefully observed. During the operation, the sand particles in the lubrication part and the running part should be blown with air frequently. It is strictly forbidden to stick sand on each lubricating part.
5、造型机使用时,开闭手柄气阀时动作要平稳。
5. When the molding machine is used, the action should be stable when opening and closing the handle air valve.
6、每完成一次造型工作后要将工作台清理干净,才能进行第二次造型工作的开始。
6. The worktable should be cleaned up after each modeling work, then the second modeling work can be started.
7、造型机使用完毕后,要将手柄回到零(空)位,关闭各阀门,清扫设备,打扫现场,要保持设备各滑动(转动)部位的清洁和润滑,认真收检工具,模具。
7. After the molding machine is used, return the handle to the zero (empty) position, close all valves, clean the equipment and clean the site. Keep the sliding (rotating) parts of the equipment clean and lubricated. Check the tools and molds carefully.

返回新闻

手机
13930206675